Alnico Holding Magnets                               Storch Magnetics 

Alnico Holding Magnets

Alnico Holding Magnets

Applications with temperatures up to 900°F can be achieved without damage to Alnico magnetic material or Magnet Assembly.

Alnico Pot Magnet Holding Assemblies

Alnico Pot Holding Magnets are assembled with non-magnetic sleeves between the magnet and the “pot”. The absence of epoxy binder allows for high temperatures and chemical stripping applications.

Part Number	Dia. A	Length B	Tapped C
				Holding Value
1290-T-08 1290-T-10 1290-T-12 1290-T-14 1290-T-16	1/4	1/2 5/8 3/4 7/8 1	8-32	.25 .30 .38 .41 .44
1291-T-08 1291-T-10 1291-T-12 1291-T-14 1291-T-16	5/16	1/2 5/8 3/4 7/8 1	8-32	.88 1.1 1.1 1.2 1.3
1292-T-08 1292-T-10 1292-T-12 1292-T-14 1292-T-16	3/8	1/2 5/8 3/4 7/8 1	8-32	1.4 1.5 1.6 1.7 1.8
1293-T-08 1293-T-10 1293-T-12 1293-T-14 1293-T-16	1/2	1/2 5/8 3/4 7/8 1	10-32	2.4 3.0 3.1 3.2 3.5
1294-T-08 1294-T-10 1294-T-12 1294-T-14 1294-T-16	5/8	1/2 5/8 3/4 7/8 1	10-32	2.4 3.4 4.1 4.8 4.9
1295-T-08 1295-T-10 1295-T-12 1295-T-14 1295-T-16 1295-T-18 1295-T-20	3/4	1/2 5/8 3/4 7/8 1 1-1/8 1-1/4	10-32	5.4 7.4 9.1 9.3 9.4 9.5 9.7
1296-T-08 1296-T-10 1296-T-12 1296-T-14 1296-T-16 1296-T-18 1296-T-20	7/8	1/2 5/8 3/4 7/8 1 1-1/8 1-1/4	1/4-20	8.6 12.4 13.4 16.0 16.6 17.0 17.4
1297-T-08 1297-T-10 1297-T-12 1297-T-14 1297-T-16 1297-T-18 1297-T-20	1.0	1/2 5/8 3/4 7/8 1 1-1/8 1-1/4	1/4-20	7.4 11.5 14.0 15.0 16.0 16.5 17.5
1298-T-08 1298-T-10 1298-T-12 1298-T-14 1298-T-16 1298-T-18 1298-T-20	1-1/4	1/2 5/8 3/4 7/8 1 1-1/8 1-1/4	1/4-20	6.0 10.0 16.0 17.0 22.0 24.0 25.0

Tolerances: Diameter +.010 -0, length + .010, -.000

Pot magnets for applications that require greater holding values are available with Rare Earth magnetic material – Neodymium Iron Boron (NdFeB) for up to 180°F, Samarium Cobalt Magnet (SmCo) for up to 575°F.

Alnico Sleeve Magnet Holding Assemblies

The Storch brass-sleeved, Alnico round magnets are externally insulated permanent magnets. This series has been designed to supply magnetic holding in inaccessible areas, steel fixtures, tools, dies, and other steel components.  Sleeve magnets can be installed into blind holes in ferrous metal to provide maximum holding value.

Part Number	Diameter A	Length B
235-06 235-08 235-12 235-16	1/8	3/8 1/2 3/4 1
251-06 251-08 251-12 251-16	3/16	3/8 1/2 3/4 1
252-06 252-08 252-12 252-16	1/4	3/8 1/2 3/4 1
253-06 253-08 253-12 253-16	5/16	3/8 1/2 3/4 1
254-06 254-08 254-12 254-16	3/8	3/8 1/2 3/4 1
255-06 255-08 255-12 255-16	7/16	3/8 1/2 3/4 1
256-08 256-12 256-16	1/2	1/2 3/4 1
258-08 258-12 258-16	5/8	1/2 3/4 1
259-08 259-12 259-16	3/4	1/2 3/4 1
261-08 261-12 261-16	7/8	1/2 3/4 1
262-08 262-12 262-16	1	1/2 3/4 1

Tolerances: Diameter +.010 -0, length + .010, -.000

Note: Parts will be supplied magnetized through the length unless otherwise specified. Magnetized 2 poles-1 face available.

For ordering Sleeve Magnets with Rare Earth Neodymium-Iron-Boron, add -NB to the end of the part number.
For ordering Sleeve Magnets with Rare Earth Samatrium-Cobalt, add -SC to the end of the part number.

Multi-Pole Magnetic Rotor

Alnico rotor protected with brass sleeve and potted with epoxy

Part Number	No. of Poles	Angle F	Dimensions					Holding Value (lbs)
			A	B	C	D	E
2130	4	90°	1.125	.406	.750	.250	.250	16
2131	6	60°	1.375	.406	.750	.219	.250	24
2132	8	45°	.313	.781	1.250	.375	.500	70

People who visited this page also visited these Storch Magnetics pages: